|
[ Pobierz całość w formacie PDF ]
.ceomview/omlvu16217_g4/output/omlvu16217_g46.html (74 of 80) [4/3/2005 11:13:06 AM] Operating· Plug exhaust pipe to avoid unintended turbo engine operation and damage.Pushing or Towing Machinec CAUTION: Avoid injury! Never tow machine faster than 16 km/h (10mph).If possible, have someone operate steering and brakes of towed tractor.IMPORTANT: Avoid damage! Push or tow machine for short distances only.1.Push the rear and mid-PTO knobs to the disengaged/off position.2.Disengage the differential lock.3.Unlock the park brake.4.Move transmission to neutral position:· PowrReverser: Depress clutch pedal completely and move the transmissiongear and range shift levers to the N (neutral) position.Move the reverser leverto the N (neutral) position.· eHydro model: Move the range shift lever to the N (neutral) position.5.If equipped, disengage the MFWD.6.Make sure brake pedals are locked together with the brake pedal latch toslow or stop machine.Towing Loadsc CAUTION: Avoid injury! Stopping distance increases with speed andweight of towed load, and on slopes.Towed loads with or without brakes thatare too heavy for the machine or are towed too fast can cause loss of control.Consider the weight of the equipment and its load.Observe these recommended maximum road speeds, or local speed limitswhich may be lower:· If towed equipment does not have brakes, do not travel more than 32 km/h(20 mph) and do not tow loads more than 1.5 times the tractor weight.· If towed equipment has brakes, do not travel more than 40 km/h (25 mph)file:///C|/projects/jd/manuals/utility/4120-4720/.ceomview/omlvu16217_g4/output/omlvu16217_g46.html (75 of 80) [4/3/2005 11:13:06 AM] Operatingand do not tow loads more than 4.5 times the machine weight.Ensure the load does not exceed the recommended weight ratio.Add ballast torecommended maximum for machine, lighten the load, or get a heavier towingunit.The machine must be heavy and powerful enough with adequate brakingpower for the towed load.Use additional caution when towing loads underadverse surface conditions, when turning, and on inclines.1.Hitch the towed load only to the drawbar.Lock the drawbar and pin in place.2.Install a safety chain to the machine drawbar support and to the towed load.Provide only enough slack to permit turning.3.Before descending a hill, shift to a gear low enough to control machine travelspeed without having to use the brake pedals to brake the machine andinstalled implements.Using Safety Chainc CAUTION: Avoid injury! Hitch towed loads only to the drawbar toavoid rearward upset.Do not use the safety chain for towing loads.IMPORTANT: Avoid damage! Secure the towed load to the drawbar.The safetychain is designed to help control the towed load should it separate from thedrawbar.Use a chain with a strength rating greater than the gross weight of the towedload.Replace or repair the safety chain if one or more links or fittings are broken,stretched or damaged.file:///C|/projects/jd/manuals/utility/4120-4720/.ceomview/omlvu16217_g4/output/omlvu16217_g46.html (76 of 80) [4/3/2005 11:13:06 AM] Operating1.Use the appropriate adapter parts (A) to attach the safety chain to themachine drawbar support and to the towed load.Provide only enough slack topermit turning.2.Install additional attaching points (B) for the chain on drawbar to reduceslack in chain when necessary.3.Remove the safety chain and store when not in use.Raising and Lowering Roll-Over Protective Structure(ROPS)c CAUTION: Avoid injury! Do not operate machine with roll-overprotection system (ROPS) in lowered position unless low clearance operation isnecessary.Do not use seat belt with ROPS in lowered position.Raise ROPS assoon as conditions permit.Lowering ROPS Crossbarfile:///C|/projects/jd/manuals/utility/4120-4720/.ceomview/omlvu16217_g4/output/omlvu16217_g46.html (77 of 80) [4/3/2005 11:13:06 AM] OperatingMX10723, MX107241.Remove spring locking pin (A) and drilled pin (B) on each side of the ROPS.2 [ Pobierz caÅ‚ość w formacie PDF ] |
Archiwum
|